Wrapping paper GOST 8273 75 supplier. Wrapping paper

GOST 8273-75
Group K68

INTERSTATE STANDARD

WRAPING PAPER

Specifications

Packing paper. Specifications

OKP 54 3500

Date of introduction 1976-01-01

INFORMATION DATA

1. DEVELOPED AND INTRODUCED by the Ministry of Forestry Industry of the USSR
DEVELOPERS

I.A. Chizhova, O.A. Vasilyeva, Ph.D. tech. sciences

2. APPROVED AND ENTERED INTO EFFECT by Resolution of the State Committee of Standards of the Council of Ministers of the USSR dated March 24, 1975 N 721

3. INSTEAD GOST 8273-57

4. REFERENCE REGULATIVE AND TECHNICAL DOCUMENTS

5. The validity period was lifted according to Protocol No. 5-94 of the Interstate Council for Standardization, Metrology and Certification (IUS 11-12-94)

6. EDITION (November 2001) with Amendments No. 1, 2, 3, approved in January 1981, March 1985, March 1990 (IUS 3-81, 6-85, 6-90), Amendment (IUS 10-2001)

This standard applies to paper intended for packaging food products medicines and industrial products.
Mandatory requirements* for product quality are set out in clause 2.1 (table, indicators 2-5).
________________
*Valid in the territory Russian Federation(Amendment, IUS 10-2001).

1. BRANDS AND SIZES

1. BRANDS AND SIZES

1.1. Depending on the purpose and quality indicators, wrapping paper should be produced in nine grades:
A - from sulfate unbleached cellulose;
B - from sulfate wrapping pulp
B - from sulfite unbleached cellulose;
G - from sulfite wrapping pulp and wood pulp;
O - from sulfate, sulfite bleached cellulose;
О - from sulfate, sulfite bleached cellulose, sulfite, unbleached cellulose and wood pulp
D - from unbleached cellulose, semi-cellulose and wood pulp
E - from waste paper, unbleached cellulose and fibrous waste from pulp and paper production.
F - composition is not standardized.
(Changed edition, Amendment No. 1).

1.2. Paper of grades B, G, E and Zh, intended for packaging food products and medicines, must be made with a composition approved by the USSR Ministry of Health.
(Changed edition, Amendment No. 3).

1.3. Paper must be produced in rolls and sheets. The width of the rolls and the dimensions of sheet paper are established by agreement between the manufacturer and the consumer.
Maximum deviations in the size of paper of all brands should not exceed ±5 mm, in paper intended for processing in automatic machines - ±2 mm.
An example of a symbol for grade A wrapping paper with a paper weight of 1 m 90 g:
Wrapping paper grade A-90 GOST 8273.

2. TECHNICAL REQUIREMENTS

2.1a. The paper must be manufactured in accordance with the requirements of this standard according to technological regulations approved in the prescribed manner.

2.1. Paper quality indicators must comply with the standards specified in the table.

Notes:

1. By agreement with the consumer, it is allowed to produce paper of grades A, B, D weighing 1 m 90 g or more with a breaking length of at least 5000, 3300, 2400 m, respectively.

2 Paper containing in the composition more than 50% waste paper and waste from pulp and paper production is allowed to be produced:
grade E weighing 1 m 60 g or more with a breaking length of at least 2000 m;
grade Zh weighing 1 m 90-120 g with a breaking length of at least 2900 m;
weighing 1 m 130-160 g with a breaking length of at least 2700 m.

2.2. By agreement between the manufacturer and the consumer, it is allowed to produce paper of all grades without glue.

2.3. The paper is produced by machine, single-sided and double-sided smooth.

2.4. The paper should be made in natural fiber color or dyed.
For packaging bulk food products, it is allowed to use paper painted in various colors with dyes approved by the USSR Ministry of Health; The use of colored paper for packaging other food products is not allowed.

2.5. Papers of grades V, D, O and O intended for printing must be manufactured with an ash content of at least 8% and a breaking length of at least 1700 m.
(Changed edition, Amendment No. 1, 3).

2.5a. By agreement with the consumer, it is allowed to produce paper of grades A and E with a moisture content of up to 11%.
(Introduced additionally, Amendment No. 3).

2.6. Folds, tears, holes that cannot be detected during the rewinding process are allowed in rolled paper if the mass of sheets with such defects, determined according to GOST 13525.5, does not exceed 5%, and in rolled paper intended for processing on automatic machines Food Industry, - 3%.

2.7. For paper intended for processing in automatic machines, the winding of the roll paper must be uniform and tight, and the edges must be cut smooth and clean.
(Changed edition, Amendment No. 3).

2.8. The number of breaks in a roll should not exceed five, and in a roll of paper intended for processing in food processing machines, it should not exceed three.

2.9. Places of breaks in paper intended for processing in automatic machines must be glued together and marked with colored signals visible from the end of the roll.

3. ACCEPTANCE

3.1. Determination of the batch and sample size - according to GOST 8047.

3.2. If unsatisfactory test results are obtained for at least one of the indicators, repeated tests are carried out on a double sample from the same batch.
The results of repeated tests apply to the entire batch.
(Changed edition, Amendment No. 2).

4. TEST METHODS

4.1a. Sampling and preparation for testing - in accordance with GOST 8047.
(Introduced additionally, Amendment No. 2).

4.1. Conditioning of paper before testing and testing is carried out according to GOST 13523 at relative humidity air (50±2)% and temperature (23±1) °C.
Conditioning duration is at least 2 hours.
(Changed edition, Amendment No. 2, 3).

4.2. Paper sizes are determined according to GOST 21102.

4.3. When determining the mass fraction of ash, the calcination temperature is set to (575±25) °C according to GOST 7629.
(Changed edition, Amendment No. 2, 3).

5. PACKAGING, LABELING, TRANSPORTATION AND STORAGE

5.1. Packaging, labeling, storage and transportation - in accordance with GOST 1641 with the following addition:

5.1.1. The marking of paper not intended for packaging food products is supplemented with the warning label “non-food grade”.

5.2. The diameter of the roll must be at least 50 cm. At the request of consumers, a roll diameter of at least 35 cm is allowed, not intended for processing in automatic machines.

5.1-5.2. (Changed edition, Amendment No. 2).

5.3. (Deleted, Amendment No. 2).

5.4. (Deleted, Amendment No. 3).

5.5. (Deleted, Amendment No. 2).

ROSSTANDART FA on technical regulation and metrology
NEW NATIONAL STANDARDS: www.protect.gost.ru
FSUE STANDARDINFORM provision of information from the Russian Products database: www.gostinfo.ru
FA ON TECHNICAL REGULATION"Dangerous goods" system: www.sinatra-gost.ru

The standard providing for the production and characteristics of wrapping paper is GOST 8273-75. It specifies all the standards associated with this material, affecting the quality of the finished product, permissible dimensional deviations, as well as storage and transportation conditions.

Specifications

Products of Pakland LLC, manufactured in accordance with GOST, comply with all sanitary and hygiene standards and can be used in food packaging. The material does not allow moisture and grease to pass through, and is additionally used for packaging flowers, books, parcels, dishes and other consumer goods.

It is produced in rolls and sheets on modern automated equipment under the strict guidance of experienced specialists, which completely eliminates the occurrence of defects, therefore we guarantee our customers the quality of the goods we supply.

It can even be packed metal objects, but there are already certain limitations, so an individual approach is needed. Our managers are ready to advise and explain all the technical nuances of using these products.

Paper grades

The following grades of paper are available:

• O1;
• O2;

The most popular among them is grade E wrapping paper. Their quality decreases from the first to the last grade, but the same thing happens with the cost. E In this case, the performance characteristics do not drop much. This is why cheap materials are more popular.

The density of the material varies from 60 to 160 g/m2, and 80 g/m2 is the most popular today.

You can buy wrapping paper GOST 8273-75 at a low price from the Pakland company. We offer significant discounts on wholesale quantities, but we also work with retail. Our clients include both individuals and legal entities not only in Moscow and the region, but throughout Russia.

5. The validity period was lifted according to Protocol No. 5-94 of the Interstate Council for Standardization, Metrology and Certification (IUS 11-12-94)

6. EDITION (November 2001) with Amendments No. 1, 2, 3, approved in January 1981, March 1985, March 1990 (IUS 3-81, 6-85, 6-90), Amendment (IUS 10-2001)


This standard applies to paper intended for packaging food, medicine and industrial products.

Mandatory requirements* for product quality are set out in clause 2.1 (table, indicators 2-5).
________________
* Valid on the territory of the Russian Federation (Amendment, IUS 10-2001).

1. BRANDS AND SIZES

1. BRANDS AND SIZES

1.1. Depending on the purpose and quality indicators, wrapping paper should be produced in nine grades:

A - from sulfate unbleached cellulose;

B - from sulfate wrapping pulp

B - from sulfite unbleached cellulose;

G - from sulfite wrapping pulp and wood pulp;

O - from sulfate, sulfite bleached cellulose;

О - from sulfate, sulfite bleached cellulose, sulfite, unbleached cellulose and wood pulp

D - from unbleached cellulose, semi-cellulose and wood pulp

E - from waste paper, unbleached cellulose and fibrous waste from pulp and paper production.

F - composition is not standardized.

(Changed edition, Amendment No. 1).

1.2. Paper of grades B, G, E and Zh, intended for packaging food products and medicines, must be made with a composition approved by the USSR Ministry of Health.

(Changed edition, Amendment No. 3).

1.3. Paper must be produced in rolls and sheets. The width of the rolls and the dimensions of sheet paper are established by agreement between the manufacturer and the consumer.

Maximum deviations in the size of paper of all brands should not exceed ±5 mm, in paper intended for processing in automatic machines - ±2 mm.

An example of a symbol for grade A wrapping paper with a paper weight of 1 m 90 g:

Wrapping paper grade A-90 GOST 8273.

2. TECHNICAL REQUIREMENTS

2.1a. The paper must be manufactured in accordance with the requirements of this standard according to technological regulations approved in the prescribed manner.

2.1. Paper quality indicators must comply with the standards specified in the table.

Notes:

1. By agreement with the consumer, it is allowed to produce paper of grades A, B, D weighing 1 m 90 g or more with a breaking length of at least 5000, 3300, 2400 m, respectively.

2 Paper containing in the composition more than 50% waste paper and waste from pulp and paper production is allowed to be produced:

grade E weighing 1 m 60 g or more with a breaking length of at least 2000 m;

grade Zh weighing 1 m 90-120 g with a breaking length of at least 2900 m;

weighing 1 m 130-160 g with a breaking length of at least 2700 m.

2.2. By agreement between the manufacturer and the consumer, it is allowed to produce paper of all grades without glue.

2.3. The paper is produced by machine, single-sided and double-sided smooth.

2.4. The paper should be made in natural fiber color or dyed.

For packaging bulk food products, it is allowed to use paper painted in various colors with dyes approved by the USSR Ministry of Health; The use of colored paper for packaging other food products is not allowed.

2.5. Papers of grades V, D, O and O intended for printing must be manufactured with an ash content of at least 8% and a breaking length of at least 1700 m.

(Changed edition, Amendment No. 1, 3).

2.5a. By agreement with the consumer, it is allowed to produce paper of grades A and E with a moisture content of up to 11%.

(Introduced additionally, Amendment No. 3).

2.6. Folds, tears, holes that cannot be detected during the rewinding process are allowed in rolled paper if the mass of sheets with such defects, determined according to GOST 13525.5, does not exceed 5%, and in rolled paper intended for processing in food processing machines, - 3%.

2.7. For paper intended for processing in automatic machines, the winding of the roll paper must be uniform and tight, and the edges must be cut smooth and clean.

(Changed edition, Amendment No. 3).

2.8. The number of breaks in a roll should not exceed five, and in a roll of paper intended for processing in food processing machines, it should not exceed three.

2.9. Places of breaks in paper intended for processing in automatic machines must be glued together and marked with colored signals visible from the end of the roll.

3. ACCEPTANCE

3.1. Determination of the batch and sample size - according to GOST 8047.

3.2. If unsatisfactory test results are obtained for at least one of the indicators, repeated tests are carried out on a double sample from the same batch.

The results of repeated tests apply to the entire batch.

(Changed edition, Amendment No. 2).

4. TEST METHODS

4.1a. Sampling and preparation for testing - in accordance with GOST 8047.

(Introduced additionally, Amendment No. 2).

4.1. Conditioning of paper before testing and testing is carried out according to GOST 13523 at relative air humidity (50±2)% and temperature (23±1) °C.

Conditioning duration is at least 2 hours.

(Changed edition, Amendment No. 2, 3).

4.2. Paper sizes are determined according to GOST 21102.

4.3. When determining the mass fraction of ash, the calcination temperature is set to (575±25) °C according to GOST 7629.

(Changed edition, Amendment No. 2, 3).

5. PACKAGING, LABELING, TRANSPORTATION AND STORAGE

5.1. Packaging, labeling, storage and transportation - in accordance with GOST 1641 with the following addition:

5.1.1. The marking of paper not intended for packaging food products is supplemented with the warning label “non-food grade”.

5.2. The diameter of the roll must be at least 50 cm. At the request of consumers, a roll diameter of at least 35 cm is allowed, not intended for processing in automatic machines.

5.1-5.2. (Changed edition, Amendment No. 2).

5.3. (Deleted, Amendment No. 2).

5.4. (Deleted, Amendment No. 3).

5.5. (Deleted, Amendment No. 2).

The text of the document is verified according to:
official publication

M.: IPK Standards Publishing House, 2001

INTERSTATE STANDARD

WRAPING PAPER

TECHNICAL CONDITIONS

Official publication

IPC PUBLISHING HOUSE OF STANDARDS Moscow

INTERSTATE STANDARD

WRAPING PAPER Technical specifications

Packing paper. Specifications

Date of introduction 01/01/76

This standard applies to paper intended for packaging food, medicine and industrial products.

(Changed edition, Amendment No. 3).

1. BRANDS AND SIZES

1.1. Depending on the purpose and quality indicators, wrapping paper should be produced in nine grades:

A - from sulfate unbleached cellulose;

B - from sulfate wrapping pulp;

B - from sulfite unbleached cellulose;

G - from sulfite wrapping pulp and wood pulp;

O] - from sulfate, sulfite bleached cellulose;

0 2 - from sulfate, sulfite bleached cellulose, sulfite unbleached cellulose and wood pulp;

D - from unbleached cellulose, semi-cellulose and wood pulp;

E - from waste paper, unbleached cellulose and fibrous waste from pulp and paper production.

F - composition is not standardized.

(Changed edition, Amendment No. 1).

1.2. Paper of grades B, G, E and Zh, intended for packaging food products and medicines, must be made with a composition approved by the USSR Ministry of Health.

1.3. Paper must be produced in rolls and sheets. The width of the rolls and the dimensions of sheet paper are established by agreement between the manufacturer and the consumer.

Maximum deviations in the size of paper of all brands should not exceed +5 mm, in paper intended for processing on automatic machines - +2 mm.

An example of a symbol for grade A wrapping paper with a paper weight of 1 m2 90 g:

Wrapping paper grade A-90 GOST 8273.

Official publication

Reproduction is prohibited

© Standards Publishing House, 1975 © And PC Standards Publishing House, 1998 Reissue with Changes

2. TECHNICAL REQUIREMENTS

2.1a. The paper must be manufactured in accordance with the requirements of this standard according to technological regulations approved in the prescribed manner.

(Introduced additionally, Amendment No. 2).

2.1. Paper quality indicators must comply with the standards specified in the table.

Notes:

1. By agreement with the consumer, it is allowed to produce paper of grades A, B, D weighing 1 m2 90 g or more with a breaking length of at least 5000, 3300, 2400 m, respectively.

2. Paper containing in the composition more than 50% waste paper and waste from pulp and paper production is allowed to be produced:

grade E weighing 1 m2 60 g or more with a breaking length of at least 2000 m; grade Zh weighing 1 m 2 90-120 g with a breaking length of at least 2900 m, weighing 1 m 2 130-160 g with a breaking length of at least 2700 m.

(Changed edition, Rev. JV° 1, 3).

2.2. By agreement between the manufacturer and the consumer, it is allowed to produce paper of all grades without glue.

2.3. The paper is produced by machine, single-sided and double-sided smooth.

2.4. The paper should be made in natural fiber color or dyed.

For packaging bulk food products, it is allowed to use paper painted in various colors with dyes approved by the USSR Ministry of Health; The use of colored paper for packaging other food products is not allowed.

2.5. Paper grades V, D, O] and 0 2 intended for printing must be manufactured with an ash content of at least 8% and a breaking length of at least 1700 m.

(Changed edition, Amendment No. 1, 3).

2.5a. By agreement with the consumer, it is allowed to produce paper of grades A and E with a moisture content of up to 11%.

(Introduced additionally, Amendment No. 3).

2.6. Folds, tears, holes that cannot be detected during the rewinding process are allowed in rolled paper if the mass of sheets with such defects, determined according to GOST 13525.5, does not exceed 5%, and in rolled paper intended for processing in food processing machines, - 3%.

2.7. For paper intended for processing in automatic machines, the winding of the roll paper must be uniform and tight, and the edges must be cut smooth and clean.

(Changed edition, Amendment No. 3).

2.8. The number of breaks in a roll should not exceed five, and in a roll of paper intended for processing in food processing machines, it should not exceed three.

2.9. Places of breaks in paper intended for processing in automatic machines must be glued together and marked with colored signals visible from the end of the roll.

3. ACCEPTANCE

3.1. Determination of the batch and sample size - according to GOST 8047.

3.2. If unsatisfactory test results are obtained for at least one of the indicators, repeated tests are carried out on a double sample from the same batch.

The results of repeated tests apply to the entire batch.

(Changed edition, Amendment No. 2).

4. TEST METHODS

4.1a. Sampling and preparation for testing - in accordance with GOST 8047.

(Introduced additionally, Amendment No. 2).

4.1. Conditioning of paper before testing and testing is carried out according to GOST 13523 at relative air humidity (50+2)% and temperature (23+1) °C.

Conditioning duration is at least 2 hours.

(Changed edition, Amendment No. 2, 3).

4.2. Paper sizes are determined according to GOST 21102.

4.3. When determining the mass fraction of ash, the calcination temperature is set to (575+25) °C according to GOST 7629.

(Changed edition, Amendment No. 2, 3).

5. PACKAGING, LABELING, TRANSPORTATION AND STORAGE

5.1. Packaging, labeling, storage and transportation - in accordance with GOST 1641 with the following addition:

5.1.1. The marking of paper not intended for packaging food products is supplemented with the warning label “non-food grade”.

5.2. The diameter of the roll must be at least 50 cm. At the request of consumers, a roll diameter of at least 35 cm is allowed, not intended for processing in automatic machines.

5.1-5.2. (Changed edition, Amendment No. 2).

5.3. (Deleted, Amendment No. 2).

5.4. (Deleted, Amendment No. 3).

5.5. (Deleted, Amendment No. 2).

INFORMATION DATA

1. DEVELOPED AND INTRODUCED BY THE USSR Ministry of Forestry Industry DEVELOPERS

I.A. Chizhova, O.A. Vasilyeva, Ph.D. tech. sciences

2. APPROVED AND ENTERED INTO EFFECT by Resolution of the State Committee of Standards of the Council of Ministers of the USSR dated March 24, 1975 N° 721

3. INSTEAD GOST 8273-57

4. REFERENCE REGULATIVE AND TECHNICAL DOCUMENTS

5. The validity period was lifted according to Protocol No. 5-94 of the Interstate Council for Standardization, Metrology and Certification (NUS 11-12-94)

6. REISSUE (October 1998) with Amendments No. 1, 2, 3, approved in January 1981, March 1985, March 1990 (NUS 3-81, 6-85, 6-90)

Editor M.I. Maksimova Technical editor Y.S. Grishanova Proofreader O.V. Ladle

Computer layout E.I. Martemyanova

Ed. persons No. 021007 dated 08/10/95. Delivered for set 09.29.98. Signed for publication on November 23, 1998. Uel. oven l. 0.93. Academic ed. l. 0.48.

Circulation 271 copies. C1450. Zach. 809.

IPK Standards Publishing House, 107076, Moscow, Kolodezny per., 14.

Typed at the Publishing House on a PC

Branch of IPK Standards Publishing House - type. “Moscow Printer”, Moscow, Lyalin lane, 6.

Plr No. 080102

to GOST 8273 75* Wrapping paper. Specifications

* The amendment is valid on the territory of the Russian Federation.

Interstate standard GOST 8273-75
"Wrapping paper. Technical specifications"
(approved by Decree of the USSR State Standard of March 24, 1975 N 721)

Packing paper. Specifications

Instead of GOST 8273-57

1. Brands and sizes

1.1. Depending on the purpose and quality indicators, wrapping paper should be produced in nine grades:

A - from sulfate unbleached cellulose;

B - from sulfate wrapping pulp;

B - from sulfite unbleached cellulose;

G - from sulfite wrapping pulp and wood pulp;

From sulfate, sulfite bleached pulp;

From sulphate, sulphite bleached pulp, sulphite unbleached pulp and wood pulp;

D - from unbleached cellulose, semi-cellulose and wood pulp;

E - from waste paper, unbleached cellulose and fibrous waste from pulp and paper production.

F - composition is not standardized.

(Changed edition, Amendment No. 1).

1.2. Paper of grades B, G, E and Zh, intended for packaging food products and medicines, must be made with a composition approved by the USSR Ministry of Health.

(Changed edition, Amendment No. 3).

1.3. Paper must be produced in rolls and sheets. The width of the rolls and the dimensions of sheet paper are established by agreement between the manufacturer and the consumer.

Maximum deviations in the size of paper of all brands should not exceed mm, in paper intended for processing in automatic machines - mm.

An example of a symbol for grade A wrapping paper with a paper weight of 1 90 g:

Wrapping paper grade A-90 GOST 8273.

(Changed edition, Amendment No. 2, 3).

2. Technical requirements

2.1a. The paper must be manufactured in accordance with the requirements of this standard according to technological regulations approved in the prescribed manner.

(Introduced additionally, Amendment No. 2).

2.1. Paper quality indicators must comply with the standards specified in the table.